ecosalix.lt

Raskite prekes pagal kategoriją:
Prekių katalogas


Kam reikalinga apšvietimo modernizacija?
  Finansinė nauda   Papildoma nauda

Paslaugos
  Pirminė konsultacija   Energijos suvartojimo analizė   Šviestuvo demonstracija   Darbas su projektu


Grįžti atgal

Compact office DIM



compact office DIM

Description

  • Presence detector (PIR)
  • Square detection area
  • Mixed light measurement
  • Light switching output (relay, 230 V) and 1-10 V interface
  • Automatic lighting control with constant light control
  • Choice of fully or semi automatic operation
  • Possible connection of sensor for manual switching and dimming
  • Brightness threshold, self-learning switch-off delay and stand-by time are adjustable
  • Fully or semi-automatic: In "Fully automatic" mode, the lighting switches on and off automatically according to presence and light. In "Semi-automatic" mode, it must be switched on manually and it switches off automatically
  • Manual override: The lighting can be manually controlled at any time using the sensor
  • The stand-by time guarantees a minimum brightness and provides for a sense of security in hospital and care environments as the lighting does not switch off when araes are unoccupied but remains in stand-by mode for the set time
  • Master/slave parallel switching: Up to ten detectors can be connected with each other to extend the detection area. The master switches the load. All other detectors merely provide presence information as slaves
  • Master/master parallel switching: Up to ten detectors can be connected with each other to control several lighting groups. Each master controls its lighting group according to its own brightness measurements. Presence is detected by all the detectors
  • Master or slave operating mode is selected via configuration
  • A maximum of 10 detectors can be switched at the same time
  • The switching behaviour of the presence detector is controlled by presence and light.
  • The self-learning switch-off delay adjusts to occupants' behaviour
  • The presence detector has mixed light measurement and is suitable for switching the following types of lamps: fluorescent lamps (FL/PL), halogen and incandescent lamps as well as LEDs
  • The square detection area allows accurate and simple planning
  • Test operation mode checks the detection area and installation
  • The parameters can either be set using the potentiometer or via the optional service remote control QuickSet plus

 

Technical data

 

compact office DIM

Operating voltage

230 V AC

Frequency

50 Hz

Recommended installation height

2 – 3 m

Installation type

Ceiling installation

Power consumption

0,8 W

Light measurement

Mixed light measurement

Setting range brightness

10 – 1500 lx

Light switch-off delay 

10 s-20 min

Stand-by time light

0 s – 60 min

Type of contact light

Relay 230 V

Lamps

Incandescent/halogen lamps, fluorescent lamps, energy saving lamps, LEDs

Resistive load

1400 VA

Incandescent/halogen lamp load

1200 W

Compact and flourescent lamps

960 VA (cos f = 0,8), 580 VA (cos f = 0,5)

Compact and flourescent lamps (Number of electronic ballasts)

10 x (1 x 58 W), 5 x (2 x 58 W), 16 x (1 x 36 W), 8 x (2 x 36 W), 16 x (smaller than 36 W)

Control output

1-10 V DC/100 mA as per EN 60929/A1

Type of connection

Screw terminals

Max. cable cross section

2 x 2,5 mm²

Mounting plate

70 x 70 mm

Size of concealed housing

Ø 55 mm (NIS, PMI)

Ambient temperature

+0 °C … +50 °C

Type of protection

IP 40 (when fitted)





Populiariausi: tifanymazmenine_prekyba_ne_maisto_prekemisligoninesapie, tifanymazmenine_prekyba_ne_maisto_prekemisligonines, tifanymazmenine_prekyba_ne_maisto_prekemispatalpu_tipai, tifanymazmenine_prekyba_ne_maisto_prekemis, tifanyapsvietimo_sprendimailigonines, tifanyapsvietimo_sprendimai, balastas200apie_mus, chanel, loremipsum0.69739323642314, vans,